﹡For detailed instructions on how to use the Digital Pen, see the User Manual stored on the CD.

Step by Step Guide to Get Started                              

Step1  Charge the Battery

For initial use, your base unit needs to be charged for about 3 hours.

Connect your base unit to your PC using the USB cable for charging.

Step2   Installing Pen Batteries

a.       Remove the battery compartment cover.

b.       Install two SR41 batteries, with the positive poles facing up as shown (Use the enclosed SR41 batteries).

c.       Replace battery compartment cover.

 WARNING:

Do not attempt to open the pen. This may cause the pen to malfunction.

Step3   Installing Ink Refill

To insert a new refill,

1.    Slide the new refill into the tip of the pen.

2.    Gently press the new refill until it is lodged securely in place.

To replace the ink refill,

1.Detach the cap from the digital pen. 

2.Clamp the ink refill with the refill extractor. Hold the pen firmly, and apply pressure with the extractor against it.

3.Pull the used refill out.

Step4   Turn On the Base Unit

Press and hold the Power button on the base unit.

Step5  Clip your Base unit on a Paper

Clip the base unit to the paper. Your Digital Pen can support a paper size of up to A4. The following illustrations show how to clip the base unit to the paper.

1.Hold the base unit and gently press the clip.

2.Slide the base unit into the paper’s top center.

Step6  Start writing

When you pick up the pen, find a position that is comfortable for you. Be careful to hold the pen in a way that does not block the signals sent from the tip of the pen to the memory unit receivers. When you are writing with the pen, make sure its inclination to the paper surface is between 45°and 90°.

Hold the pen firmly and write normally.

Note: Make sure the pen point is 1.5cm away from the unit. Otherwise, the unit sensor may not work.

Buttons & Ports       

a.     USB port – connect to computer through the USB cable.

b.    Neck Strap Holder c.  LCD display

d.    Power button – Press and hold for about 5 seconds to turn on or off the unit.

Press briefly to create a new note.

e.     Bluetooth ON/OFF – Turn on or off the bluetooth.

f.     Reset hole – When the unit does not respond, insert a pinpoint into this hole to reset the device and then press and hold the Top button to restart the unit.

g.    Paper Clip – clip the unit to paper.

Memory Unit LCD         

Use the LCD to view status indications.

Create Note in Mobile Mode

To take handwritten note when you are away from computer,

(1) Press and hold the ON/OFF button to power on the unit.

(2)  Hold the base unit and gently press the paper clipper.

(3)  Slide the base unit into the paper’s upper edge and make sure the base unit is in the center.

(4)  Pick up the pen and start writing. (NOTE: Be careful to hold the pen in a way that does not block signals sent from the tip of the pen to the receiver unit.)

 (5)  Once you’ve completed one page, shortly press the ON/OFF button to save current page and start a new page. On the base unit screen, you can see the page number added by one.

(6)  All notes are stored in the base unit. You can upload them to a PC for viewing, editing, or email.

 

Create Note in On line Mode                                                      

Connecting your Digital Pen to your computer and drawing with your Digital Pen in Note mode can create a new note. Everything you write is being captured automatically. Before doing so, make sure the Note Manager is installed and running on your computer.

Once you have finished with your note, you can use the Note Manager to save your note to a picture file, then email it, print it, or simply save it to your Note Manager for later use.

 

 Use your Digital Pen as a Mouse

The device can behave as a mouse, performing the click and hovering function.

Make sure you have connected the base unit to your PC before using the Mouse function

 

· Start your Note Manager application > right click the application tray icon> select   · “Mouse Mode”. Press the top button (ON/OFF button) on the base unit. · Click the virtual area using your pen.

Changing to Mouse mode can be done in 3 ways:

In Mouse mode, your Digital Pen behaves as a mouse, having the following functionality:

•  To move your mouse cursor you can hover with the pen.

To start Hovering you can press the side button or tip the pen on the paper. The pen will now hover even with no press for about 30 seconds.

•  To Click an object, point your mouse cursor on that object. Now tip the pen on the paper or click the side button.
•  To Double-Click an object, point your mouse cursor on that object.

Now tip the pen twice on the paper or click the side button twice.

•  To Right-Click an object, point your mouse cursor on that object. Now press the tip of the pen a bit longer on the paper. A special ‘Right Click’ cursor will appear. Lift thepen from the paper, and the context menu (Right Click menu) appears.

Using your Digital Pen in Window XP/2000                          

1. Installing the Note Manager

The CD contains the Note Manager software which is required. Simply insert the CD and then follow the wizard's instructions.

2. Connecting your Digital Pen to your Computer.

3. Uploading your Mobile Notes

First make sure your Note Manager is running. Now simply connect your base unit to your

USB port.

The Note Manager application will detect your unit and will prompt you to upload your notes.

Select “Yes” to start transferring your notes.

4. Using the Note Manager

The Note Manager can be used for storing,viewing, searching, copying and exporting notes. It is set up in Windows Explorer format, which allows you to browse through your files in the left pane and view them in the right pane.

The Note Manager contains buttons that give you access to the most commonly used menu commands.