Before installing your scanner, please verify that you have all of the proper components. A list of the package contents is provided in the Box Contents section of this guide.
Software Installation Requirements
Your scanner comes with the image-editing software (Presto! ImageFolio), the scanner’s driver and FotoLite software. All of these software applications use approximately 160 megabytes of hard disk space after they are installed into your computer. To ensure ample room for the installation, as well as for scanning and saving images, a minimum of 260 megabytes of hard disk space is recommended.
The USB scanner can only operate under the Microsoft Windows Vista, 2000 Professional, XP or Windows 7 operating system.
Hardware Requirements
This scanner connects to your computer through the Universal Serial Bus (USB) which supports hot Plug and Play.To determine whether your computer is USB- capable, you must check the rear of your PC to locate a USB jack that looks the same as the one pictured below. Note that on some computers, the USB port at the rear of the computer may be occupied and additional ports may be found on the monitor or keyboard. If you are having trouble in locating the USB port on your computer, please refer to the hardware manual that came with your computer.
Upon examination, you should find one or two rectangular USB ports, which usually appear as shown below.
If you don’t find such USB ports on your computer, then you need to purchase a certified USB interface card to add USB capabilities to your computer.
Installing and Setting up the Scanner
Please follow the step-by-step procedures described below to install the scanner.
• Please make sure your scanner is DISCONNECTED to your computer before you perform the installation.
• If you connect your scanner to the computer before installation, and Attention the window “Found New Hardware Wizard” pops up, please click “Cancel” to exit the window, disconnect the scanner from your computer, and perform the following installation steps.
For Windows 2000 & XP
1. Installing the Software
a. Insert the Setup/Application CD-ROM, included with your scanner, into your CD-ROM drive.
b. Click on the “Install the Software” button in the installation wizard window that pops up.
c. Click on the “Install” button to start the installation.
d. Click on the [Next] button in the window that appears.
e. During the process of the installation, a message “Digital Signature required” might be prompted.Please ignore it, and click on [Yes] to continue the installation without any misgiving at your scanner functioning.
f. A dialog will pop up, noticing you to connect the scanner. Please connect the scanner to your computer now, and click “OK” when the installation is completed.
2. Connecting the Scanner to Your Computer
A. Plug the smaller end of the included USB cable to the USB port on the scanner, and plug the bigger end of the USB cable to the USB port on your computer.
B. Or, if you plan to connect your scanner to a USB hub3, make sure that the hub is connected to the USB port in your computer. Next, connect the scanner to the USB hub.
Note: If you are using a USB hub, we recommend that you use one with its own external power adapter.
3. Finish the Installation and Restart the Computer
a. If the USB components on your computer are functioning correctly, they will automatically detect the scanner causing the “Add New Hardware Wizard” or “Found New Hardware Wizard” to be launched. Select any option in the window and click “Next”.
Note: If your computer was off when you connected the scanner, the “Add New Hardware Wizard” message will be displayed when you turn the computer on and when Windows starts.
b. Select “Install the software automatically (Recommended)” and click on the [Next] button. The “Windows Logo” dialog will be prompted again, please select “Continue Anyway”.
c. When the system completes the installation, click on the [Finish] button.
d. Follow the on-screen instructions to install all software that your new USB scanner requires.The USB hub is not included with the scanner.
e. After the software is installed, close all open applications and click on the [Finish] button to restart your computer.
For Windows Vista & 7
1. Installing the Software
a. Insert the Setup/Application CD-ROM, included with your scanner, into your CD-ROM drive. Select “Run” in the AutoPlay window that appears.
b. For Vista users - Click on the [Continue] button when the “User Account Control” dialog pops up.
c. Click on the “Install the Software” button in the installation wizard window that pops up.
d. Click on the “Install” button to start the installation.
e. Click on the [Next] button in the window that appears.
f. During the process of the installation, a message “Would you like to install this device software? Name: Jungo, Publisher: Jungo LTD.” will appear, please select “Install”.
g. During the process of the installation, a message “Windows can’t verify the publisher of this driver software” may appear. Please ignore and click on “Install this drive software anyway” to continue the installation.
h. A dialog will pop up, noticing you to connect the scanner. Please connect the scanner to your computer now, and click “OK” when the installation is completed.
2. Connecting the Scanner to Your Computer
A. Plug the smaller end of the included USB cable to the USB port on the scanner, and plug the bigger end of the USB cable to the USB port on your computer.
B. Or, if you plan to connect your scanner to a USB hub4, make sure that the hub is connected to the USB port in your computer. Next, connect the scanner to the USB hub.
Note: If you are using a USB hub, we recommend that you use one with its own external power adapter.
3. Finish the Installation and Restart the Computer
a. When the system completes the installation, click on the [Finish] button.
b. Follow the on-screen instructions to install all software that your new USB scanner requires.
c. After the software is installed, close all open applications and click on the
[Finish] button to restart your computer.
Attention If the scanner installation is not started and displayed automatically on the screen, click [Start], select [Run] and type in [d:\Install] (where d: is the drive letter assigned to the CD-ROM drive of your computer.)
Software Setup Troubleshooting
Carefully review the steps outlined in this guide and the Quick Installation Guide that accompanied your scanner.
If you are still having problems, please check that:
• You have 500MB of free space on your hard disk drive.
• The scanner is plugged in and has power.
• You are using the USB cable supplied with the scanner.
• The square end of the USB cable is plugged into the rear of the scanner.
• The rectangular end of the USB cable is plugged into the back of your computer.
If you deviated from the installation procedures defined in this manual, please unplug the USB cable from the scanner and reinstall the software from the CD-ROM. To reinstall your scanner’s software, click [Start], [Run], then type [D:\Install] (where D represents the letter of your CD-ROM drive). Carefully follow all the installation instructions presented in the Setup Wizard. Reboot your computer when prompted, and plug the USB cable back into the scanner while your computer is still turned on.
Installing Additional Software
Your scanner is TWAIN compliant and functions with virtually all available TWAIN compatible software. If you purchase additional software to be used with your scanner, please make sure that it conforms to the TWAIN standard.
4 The USB hub is not included with the scanner.
Loading... 